Develon · Relays
Develon Starter, pilot and speed relays fault codes
Relay outputs that the machine controller uses for starting, the reversing buzzer, the pilot cut-off, inching and the low and high speed ranges. A relay circuit fault stops that function from switching.
Where this code shows
Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.
What do these codes mean?
Develon codes V000234 to V000267 are all about the starter, pilot and speed relays. None needs an immediate stop. Start with this check: locate the relay named in the code and swap it with an identical one.
How urgent are they?
None of the 6 codes here means stop now; all 6 can wait until the shift ends, but find the cause before the next one.
- Check soon6
What should I check first?
Locate the relay named in the code and swap it with an identical one.
Shared checksStop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Develon V000234Starter relay
The starter relay output is the controller's drive for cranking the engine. A fault here usually means the engine will not crank, or cranks only sometimes, because the relay is not being switched.· OtherOtherCheck soonCauses
- Failed relay coil or burnt contacts
- Loose or corroded relay socket pin
- Open or shorted drive wire from the controller
- Blown fuse in the relay supply
Checks
- 1Swap the starter relay with an identical one and see whether the code follows it.
- 2Measure battery voltage and a good ground at the socket while turning the key to start.
- 3Check the drive wire from the controller for continuity with the relay removed.
- 4Inspect the socket for heat marks and green corrosion.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon V000235Back buzzer relay
Same failure as V000234 on the back buzzer relay, a different part of the same kind as the starter relay. Specific to this code: the table names it 'Back buzzer relay'.· OtherOtherCheck soonCauses
- Fault in the back buzzer relay or its wiring
- Any cause listed under V000234
Checks
- 1Check the back buzzer relay connector and wiring first, then follow the checks listed under V000234.
- 2Clear the code and confirm whether V000235 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon V000236Pilot relay
Same failure as V000234 on the pilot relay, a different part of the same kind as the starter relay. Specific to this code: the table names it 'Pilot relay'.· OtherOtherCheck soonCauses
- Fault in the pilot relay or its wiring
- Any cause listed under V000234
Checks
- 1Check the pilot relay connector and wiring first, then follow the checks listed under V000234.
- 2Clear the code and confirm whether V000236 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon V000265Inching relay
Same failure as V000234 on the inching relay, a different part of the same kind as the starter relay. Specific to this code: the table names it 'Inching relay'.· OtherOtherCheck soonCauses
- Fault in the inching relay or its wiring
- Any cause listed under V000234
Checks
- 1Check the inching relay connector and wiring first, then follow the checks listed under V000234.
- 2Clear the code and confirm whether V000265 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon V000266Low speed relay
Same failure as V000234 on the low speed relay, a different part of the same kind as the starter relay. Specific to this code: the table names it 'Low speed relay'.· OtherOtherCheck soonCauses
- Fault in the low speed relay or its wiring
- Any cause listed under V000234
Checks
- 1Check the low speed relay connector and wiring first, then follow the checks listed under V000234.
- 2Clear the code and confirm whether V000266 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon V000267High speed relay
Same failure as V000234 on the high speed relay, a different part of the same kind as the starter relay. Specific to this code: the table names it 'High speed relay'.· OtherOtherCheck soonCauses
- Fault in the high speed relay or its wiring
- Any cause listed under V000234
Checks
- 1Check the high speed relay connector and wiring first, then follow the checks listed under V000234.
- 2Clear the code and confirm whether V000267 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Locate the relay named in the code and swap it with an identical one.
- 2Measure battery voltage and ground at the relay socket with the function active.
- 3Check the coil drive wire back to the controller for continuity.
- 4Inspect the socket for heat marks or green corrosion.
Causes
- Failed relay or burnt contacts
- Loose relay socket pin
- Open or shorted coil drive wire
- Blown fuse for the relay circuit
When to stop
You'll notice: The machine may not start, the buzzer or pilot lock may fail to act, or speed ranges may not change, with the code shown on the monitor.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
