EF Logo

Develon · Aftertreatment

Develon DPF, DOC and regeneration fault codes

Diesel particulate filter and oxidation catalyst sensors, soot and ash monitoring and regeneration control. The controller watches pressure drop and temperature across the filter.

FaultCheckE000081Develon · DPF, DOC and regeneration
Code shows hereFAULTE000081

Where this code shows

Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.

What do these codes mean?

Develon codes E000081 to E520653 are all about the dPF, DOC and regeneration. None needs an immediate stop. Start with this check: read soot load and regeneration status in the diagnostic tool.

How urgent are they?

None of the 24 codes here means stop now; all 24 can wait until the shift ends, but find the cause before the next one.

  • Check soon24

What should I check first?

Read soot load and regeneration status in the diagnostic tool.

Shared checks

24 of 24

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Develon E000081DPF Differential Pressure High

    Same failure as E003609 on the dpf differential pressure high, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the dpf differential pressure high or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the dpf differential pressure high connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E000081 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000173DPF downstream temperature

    Same failure as E003242 on the dpf downstream temperature, a different part of the same kind as the dpf upstream temperature.· Other
    Check soon

    Causes

    • Fault in the dpf downstream temperature or its wiring
    • Any cause listed under E003242

    Checks

    1. 1Check the dpf downstream temperature connector and wiring first, then follow the checks listed under E003242.
    2. 2Clear the code and confirm whether E000173 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E003242DPF upstream temperature

    A DPF temperature sensor reading is missing or implausible.· Erratic or implausible
    Check soon

    Causes

    • Failed exhaust temperature sensor
    • Open or shorted wire
    • Exhaust leak near the sensor
    • Corroded connector

    Checks

    1. 1Compare the temperature readings of the other aftertreatment sensors on the same line.
    2. 2Measure the sensor resistance at ambient and compare with the manual curve.
    3. 3Inspect the wire for heat damage near the exhaust.
    4. 4Check for exhaust leaks around the sensor mount.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Develon E003609DPF pressure sensor physical range check

    The DPF pressure sensor reading is outside the physical range the controller allows.· Other
    Check soon

    Causes

    • Failed differential-pressure sensor
    • Split, kinked or blocked sensor hose
    • Connector moisture
    • Real blockage in the filter

    Checks

    1. 1Inspect both sensor hoses for splits, kinks and loose clamps.
    2. 2Check the 5 V supply and ground at the sensor connector.
    3. 3Read the value with the engine off; it should be near zero differential.
    4. 4Check soot load and regeneration status in the tool.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E003719Maximum soot mass in particulate filter

    Same failure as E003609 on the maximum soot mass in particulate filter, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the maximum soot mass in particulate filter or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the maximum soot mass in particulate filter connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E003719 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E004765DOC upstream temperature

    Same failure as E003242 on the doc upstream temperature, a different part of the same kind as the dpf upstream temperature.· Other
    Check soon

    Causes

    • Fault in the doc upstream temperature or its wiring
    • Any cause listed under E003242

    Checks

    1. 1Check the doc upstream temperature connector and wiring first, then follow the checks listed under E003242.
    2. 2Clear the code and confirm whether E004765 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E004767Diesel oxidation catalyst differential pressure

    Same failure as E003609 on the diesel oxidation catalyst differential pressure, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the diesel oxidation catalyst differential pressure or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the diesel oxidation catalyst differential pressure connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E004767 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E010024Exhaust Temperature Sensor 2 Fault

    Same failure as E003242 on the exhaust temperature sensor 2 fault, a different part of the same kind as the dpf upstream temperature.· Other
    Check soon

    Causes

    • Fault in the exhaust temperature sensor 2 fault or its wiring
    • Any cause listed under E003242

    Checks

    1. 1Check the exhaust temperature sensor 2 fault connector and wiring first, then follow the checks listed under E003242.
    2. 2Clear the code and confirm whether E010024 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E010025DPF Lamp Fault

    Same failure as E003609 on the dpf lamp fault, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the dpf lamp fault or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the dpf lamp fault connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E010025 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E010026DPF PM Over

    Same failure as E003609 on the dpf pm over, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the dpf pm over or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the dpf pm over connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E010026 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E010027DPF Regeneration Defective

    Same failure as E003609 on the dpf regeneration defective, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the dpf regeneration defective or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the dpf regeneration defective connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E010027 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E010028DPF Exhaust Temperature 2

    Same failure as E003242 on the dpf exhaust temperature 2, a different part of the same kind as the dpf upstream temperature.· Other
    Check soon

    Causes

    • Fault in the dpf exhaust temperature 2 or its wiring
    • Any cause listed under E003242

    Checks

    1. 1Check the dpf exhaust temperature 2 connector and wiring first, then follow the checks listed under E003242.
    2. 2Clear the code and confirm whether E010028 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E010029DPF Regeneration Timeout Excess Frequency

    Same failure as E003609 on the dpf regeneration timeout excess frequency, a different part of the same kind as the dpf pressure sensor physical range check.· Lost message
    Check soon

    Causes

    • Fault in the dpf regeneration timeout excess frequency or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the dpf regeneration timeout excess frequency connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E010029 returns on its own.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon E520605DPM system error

    Same failure as E003609 on the dpm system error, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the dpm system error or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the dpm system error connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E520605 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520620Completely damaged particulate filter

    Same failure as E003609 on the completely damaged particulate filter, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the completely damaged particulate filter or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the completely damaged particulate filter connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E520620 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520621Mon pressure differential characteristics

    Same failure as E003609 on the mon pressure differential characteristics, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the mon pressure differential characteristics or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the mon pressure differential characteristics connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E520621 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520622Disconnected DPF pressure sensor hose line

    Same failure as E003609 on the disconnected dpf pressure sensor hose line, a different part of the same kind as the dpf pressure sensor physical range check.· Open circuit
    Check soon

    Causes

    • Fault in the disconnected dpf pressure sensor hose line or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the disconnected dpf pressure sensor hose line connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E520622 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Develon E520646DPF Pressure sensor hose line check

    Same failure as E003609 on the dpf pressure sensor hose line check, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the dpf pressure sensor hose line check or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the dpf pressure sensor hose line check connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E520646 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520647DPF Pressure sensor offset diagnostic

    Same failure as E003609 on the dpf pressure sensor offset diagnostic, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the dpf pressure sensor offset diagnostic or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the dpf pressure sensor offset diagnostic connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E520647 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520649Monitoring of incomplete regeneration

    Same failure as E003609 on the monitoring of incomplete regeneration, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the monitoring of incomplete regeneration or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the monitoring of incomplete regeneration connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E520649 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520650Regeneration locked

    Same failure as E003609 on the regeneration locked, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the regeneration locked or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the regeneration locked connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E520650 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520651Monitoring for maximum ash mass in DPF

    Same failure as E003609 on the monitoring for maximum ash mass in dpf, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the monitoring for maximum ash mass in dpf or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the monitoring for maximum ash mass in dpf connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E520651 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520652Forced regeneration switch

    Same failure as E003609 on the forced regeneration switch, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the forced regeneration switch or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the forced regeneration switch connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E520652 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520653Forced regeneration inhibit switch

    Same failure as E003609 on the forced regeneration inhibit switch, a different part of the same kind as the dpf pressure sensor physical range check.· Other
    Check soon

    Causes

    • Fault in the forced regeneration inhibit switch or its wiring
    • Any cause listed under E003609

    Checks

    1. 1Check the forced regeneration inhibit switch connector and wiring first, then follow the checks listed under E003609.
    2. 2Clear the code and confirm whether E520653 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Read soot load and regeneration status in the diagnostic tool.
  2. 2Inspect pressure sensor hoses for splits, kinks and loose clamps.
  3. 3Check exhaust temperature sensors against each other.
  4. 4Run the correct regeneration procedure and look for leaks upstream.

Causes

  • Loaded or damaged filter
  • Faulty differential-pressure or temperature sensor
  • Blocked or disconnected sensor hose
  • Interrupted regenerations from short running

When to stop

You'll notice: A DPF lamp or derate may show; the machine may ask for a regeneration or limit power until it is done.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.