EF Logo

Cat · Transmission check

Cat Transmission and machine circuit faults fault codes

These codes come from the transmission ECM and machine circuits: parking brake switch, fuel level and oil temperature senders, demand fan, differential lock and neutralizer solenoids or sensors, backup alarm and the transmission speed sensor. Most are voltage high or erratic data faults on a single input or output.

FaultCheckCID 70FMI 03Cat · Transmission and machine circuit faults
Code shows hereFAULTCID 70FMI 03

Where this code shows

Turn the key on and check the cluster or monitor for a warning lamp.

What do these codes mean?

Cat codes CID 70 FMI 03 to CID 740 FMI 03 are all about the transmission and machine circuit faults. Most are shorted high faults; none needs an immediate stop. Start with this check: connect Cat ET, confirm the CID is active and note the component it names.

How urgent are they?

None of the 9 codes here means stop now; 8 can wait until the shift ends, but find the cause before the next one; 1 is information only.

  • Check soon8
  • Info1

What should I check first?

Connect Cat ET, confirm the CID is active and note the component it names.

Shared checks

9 of 9

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Cat CID 70 FMI 03Parking brake switch voltage high

    The transmission ECM sees both the engaged and disengaged inputs of the parking brake switch open.· Shorted high
    Check soon

    Causes

    • Faulty parking brake limit switch
    • Open lower cab wiring harness
    • Open cab ground
    • Transmission ECM

    Checks

    1. 1Connect Cat ET to the transmission ECM and confirm 70-3 is active.
    2. 2Turn the ignition and battery disconnect off, remove the limit switch and test it.
    3. 3Inspect the harness connectors and tag anything disconnected.
    4. 4Check the cab ground for continuity to frame.
    5. 5Replace the switch or repair the harness, then the ECM last.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Cat CID 96 FMI 03Fuel level sensor voltage high

    The transmission ECM saw the fuel level sensor signal shorted to battery voltage.· Shorted high
    Check soon

    Causes

    • Rear frame wiring harness shorted
    • Lower cab wiring harness shorted
    • Transmission ECM

    Checks

    1. 1Check for 96-3 active with Cat ET connected to the transmission ECM.
    2. 2Turn off, remove the oil cooler cover and unplug connector M-C12 from the fuel level sensor.
    3. 3See whether the code changes with the sensor unplugged.
    4. 4Inspect the rear frame harness along the tank for chafing.
    5. 5Repair the harness, then the ECM if still high.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Cat CID 177 FMI 03Transmission oil temperature sensor voltage high

    The transmission ECM read the oil temperature sensor signal too high.· Shorted high
    Check soon

    Causes

    • Transmission harness open or shorted to a power source
    • Lower cab harness open or shorted to a power source
    • Faulty oil temperature sensor
    • Transmission ECM

    Checks

    1. 1Connect Cat ET to the transmission ECM and confirm 177-3 is active.
    2. 2Check for other active codes that share the sensor supply and repair those first.
    3. 3Unplug the sensor and test the harness signal wire for an open or a short to supply.
    4. 4Inspect the connector for water and corrosion.
    5. 5Replace the oil temperature sensor if the harness is clean, then repair any harness fault found.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Cat CID 291 FMI 03Demand fan solenoid voltage high

    The transmission ECM sees demand fan solenoid voltage above normal.· Shorted high
    Check soon

    Causes

    • Lower cab harness shorted to another power source
    • Rear frame harness shorted to another power source
    • Transmission ECM

    Checks

    1. 1Connect Cat ET to the transmission ECM and confirm 291-3 is active.
    2. 2With the ignition off, remove the fan and unplug connector M-C16 from the solenoid.
    3. 3Check the lower cab harness at the right access panels for a short.
    4. 4Look for harness wear at the rear frame where it flexes.
    5. 5Repair the shorted harness or replace the ECM.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Cat CID 426 FMI 03Transmission neutralizer pressure sensor voltage high

    The transmission ECM sees the neutralizer pressure sensor signal shorted to battery voltage.· Shorted high
    Check soon

    Causes

    • Lower cab wiring harness shorted to voltage
    • Sensor signal wire touching a supply wire
    • Transmission ECM

    Checks

    1. 1Connect Cat ET to the transmission ECM and confirm 426-3 is active.
    2. 2If 262-3 or 262-4 is active, repair it first.
    3. 3Turn the ignition and battery disconnect off and test the lower cab harness for a short.
    4. 4Unplug the sensor and recheck the signal on the harness side.
    5. 5Repair the shorted harness section; replace the transmission ECM only if the harness tests clean.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Cat CID 585 FMI 02Transmission speed sensor data erratic

    The transmission ECM got an unreliable signal from the output A or B speed sensor.· Erratic or implausible
    Check soon

    Causes

    • Faulty output speed sensor A or B
    • Open or shorted lower cab harness
    • Open or shorted transmission harness
    • Transmission ECM

    Checks

    1. 1Use Cat ET with the transmission ECM selected and confirm 585-2 is active.
    2. 2Inspect both output speed sensor connectors for oil and bent pins.
    3. 3Test the harness from each sensor back to the transmission ECM.
    4. 4Check the sensor air gap and the target gear for damage.
    5. 5Replace the sensor if its signal is erratic on the bench, then repair the harness if the fault remains.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Cat CID 600 FMI 03Hydraulic oil temperature sensor voltage high

    The transmission ECM reads hydraulic oil temperature sensor voltage too high.· Shorted high
    Check soon

    Causes

    • Faulty hydraulic oil temperature sensor
    • Lower cab harness open or shorted to voltage
    • Engine harness open or shorted to voltage
    • Transmission ECM

    Checks

    1. 1Connect Cat ET and confirm 600-3 is active on the transmission ECM.
    2. 2Turn off, remove the left engine access panel and inspect the sensor connector.
    3. 3Unplug the sensor and test the signal wire for an open or a short to voltage.
    4. 4Test the lower cab harness section feeding the sensor.
    5. 5Replace the sensor if its signal is erratic on the bench, then repair the harness if the fault remains.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Cat CID 637 FMI 03Backup alarm circuit voltage high

    The transmission ECM sees backup alarm circuit voltage above normal.· Shorted high
    Info

    Causes

    • Lower cab harness shorted to another power source
    • Rear frame harness shorted to another power source
    • Transmission ECM

    Checks

    1. 1Set the military light switch to SER. DRIVE and the transmission control to R with Cat ET connected.
    2. 2Turn the ignition off and test the rear frame harness at the alarm.
    3. 3Check the lower cab harness at the controller for a short.
    4. 4Inspect the backup alarm connector for water and corrosion at the pins.
    5. 5Repair the shorted harness section; replace the transmission ECM only if the harness tests clean.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Cat CID 740 FMI 03Differential lock solenoid voltage high

    The transmission ECM sees differential lock solenoid voltage above normal.· Shorted high
    Check soon

    Causes

    • Lower cab harness shorted to another power source
    • Front frame harness shorted to another power source
    • Transmission ECM

    Checks

    1. 1Connect Cat ET to the transmission ECM and confirm 740-3 is active.
    2. 2Switch off, remove the right lower cab access panels and unplug connector LE-C17 from the solenoid.
    3. 3Check whether the code clears with the solenoid unplugged.
    4. 4Test the front frame harness for a short to a power feed.
    5. 5Repair or replace the shorted harness first, and replace the transmission ECM only as a last step.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

Shared checks

Checks, in order

  1. 1Connect Cat ET, confirm the CID is active and note the component it names.
  2. 2Unplug the named component and see whether the code changes from voltage high to a different state.
  3. 3Measure the signal wire at the harness connector for contact with a power feed.
  4. 4Inspect the connector for water, oil and pushed-back pins.

Causes

  • Short to supply voltage in the circuit harness
  • Failed sensor, switch or solenoid
  • Corroded or loose connector at the component
  • Transmission ECM output or input fault (rare)

Most codes here: shorted high (8 of 9)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: A warning lamp or a transmission or machine function that stops working, such as the demand fan, differential lock or backup alarm, with a CID code in Cat ET.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.