Specification sheetIssued 20 November 2026
Komatsu · mini excavator
Komatsu PC70-8
Komatsu PC70-8 compact hydraulic excavator (Komatsu SAA4D95LE-5, EPA Tier 3 / EU Stage 3A equivalent), standard specification without blade, 1650 mm arm, 450 mm steel shoes, from Komatsu brochure CEN00471-04 (Jan 2018, Komatsu Asia). The copy used is hosted by Komatsu distributor Dimo Bangladesh; no Komatsu Middle East PC70-8 sheet was found.
UAEGlobal
- digging depth
- 13.5 ft
- power
- 65 HP
- Operating weight
- 14,528 lb
- Bucket capacity
- 0.39 yd³
8.7 ft7 ft19.9 ft
7.3 ftWorking range
- AMax digging height
- 23.5 ft
- BMax dumping height
- 16.5 ft
- CMax digging depth
- 13.5 ft
- DMax vertical wall digging depth
- 11.5 ft
- EMax digging reach
- 20.9 ft
- FMax reach at ground level
- 20.4 ft
- GMin swing radius
- 5.7 ft
- Stick length (Standard arm (lifting-capacity tables))
- 5 ft 5 in
Weight
- Operating weight (Without blade, 450 mm steel shoes, 0.30 m3 ISO 7451 heaped bucket, 1650 mm arm, with operator, full fuel tank and rated fluids)
- 14,528 lb
- Operating weight (blade) (Blade specification)
- 15,851 lb
- Operating weight (heavy-duty) (Heavy-duty specification: reinforced arm and 0.37 m3 heavy-duty bucket)
- 14,782 lb
- Ground pressure (450 mm steel shoes)
- 28.4 kPa (0.29 kg/cm2)
Performance
- Bucket capacity (Standard bucket, ISO 7451 heaped; 0.37 m3 buckets also listed (p.11))
- 0.39 yd³
- Bucket digging force (SAE J1179 rating; 5590 kg)
- 12,320 lbf
- Arm digging force (SAE J1179 crowd force; 3900 kg)
- 8,588 lbf
- Swing speed
- 11 min-1
- Travel speed (high)
- 2.8 mph
- Travel speed (low)
- 1.7 mph
- Max drawbar pull (5750 kg)
- 12,679 lbf
- Max lift capacity (Over front at 2.0 m reach, 1.0 m below ground; hydraulic-limited rating; 1650 mm arm, 0.30 m3 bucket, without blade)
- 8,245 lb
Engine
- Engine model
- Komatsu SAA4D95LE-5
- Type
- Water-cooled, 4-cycle, direct injection
- Aspiration
- Turbocharged, air-to-air aftercooled
- Emissions
- U.S. EPA Tier 3 and EU Stage 3A equivalent
- Cylinders
- 4
- Bore x stroke
- 95 x 115 mm
- Displacement
- 0.9 US gal
- Gross power (SAE J1995, at 1950 min-1)
- 68 HP
- Net power (ISO 9249 / SAE J1349, at 1950 min-1)
- 65 HP
- Fan drive
- Mechanical
- Governor
- All-speed control, electronic
Hydraulics
- System
- Closed-centre load-sensing (CLSS) with pressure-compensated valves
- Main pump
- Variable displacement axial piston
- Pump flow
- 45.4 US gpm
- Implement circuit pressure (Relief valve setting)
- 24.5 MPa (250 kg/cm2)
- Travel circuit pressure (Relief valve setting)
- 24.5 MPa (250 kg/cm2)
- Swing circuit pressure (Relief valve setting)
- 21.1 MPa (215 kg/cm2)
- Pilot circuit pressure (Relief valve setting)
- 3.1 MPa (32 kg/cm2)
- Travel motors
- Variable displacement axial piston
- Swing motor
- Fixed displacement axial piston
- Boom cylinder
- 1 - 115 mm bore x 840 mm stroke x 65 mm rod
- Arm cylinder
- 1 - 100 mm bore x 865 mm stroke x 60 mm rod
- Bucket cylinder
- 1 - 90 mm bore x 710 mm stroke x 55 mm rod
Undercarriage
- Track frame
- Box-section
- Track shoes
- Triple grouser
- Track adjuster
- Hydraulic
- Track shoes (each side)
- 38
- Track rollers (each side)
- 5
- Carrier rollers (each side)
- 1
- Swing reduction
- Planetary gear
- Swing circle lubrication
- Grease-bathed
- Service brake
- Hydraulic lock
- Parking brake
- Hydraulic release lock
- Steering control
- Two levers with pedals
Blade
- Blade width (Blade specification)
- 7.4 ft
- Blade height (Blade specification)
- 1.5 ft
- Max blade lift above ground (Blade specification)
- 1.3 ft
- Max blade drop below ground (Blade specification)
- 0.9 ft
Service capacities
- Fuel tank
- 34.3 US gal
- Cooling system (Coolant)
- 2.6 US gal
- Engine oil (Refill capacity)
- 3 US gal
- Final drive, each side
- 0.3 US gal
- Hydraulic tank
- 16.1 US gal
Service intervals
- Engine oil and filter
- 500 hours
- Hydraulic oil
- 5,000 hours
- Hydraulic oil filter
- 1,000 hours