Specification sheetIssued 20 November 2026
John Deere · mini excavator
John Deere 26 P-Tier
John Deere 26 P-Tier reduced-tail-swing mini excavator (Yanmar 3TNV80F, Final Tier 4 / Stage IV, 300 mm rubber tracks, 1.17 m arm) per Deere spec sheet ME26PAU (23-07); canopy figures unless noted. This is the sheet issued before Deere's October 2025 redesign of the 26 P-Tier; no sheet for the redesigned machine was found. The older 26G is not covered.
UAEUSAGlobal
- digging depth
- 8 ft. 6 in.
- power
- 20.0 hp
- Operating weight
- 5,780 lb.
8 ft13.7 ft
Dimensions
- Overall length (blade in rear)
- 14 ft. 8 in.
Performance
- AMax digging reach (1.17 m standard arm)
- 15 ft. 2 in.
- BMax digging depth
- 8 ft. 6 in.
- CMax cutting height (canopy; cab 4.28 m)
- 14 ft. 7 in.
- DMax dumping height (canopy; cab 3.04 m)
- 10 ft. 6 in.
- GMinimum swing radius (front swing radius; cab 2.01 m)
- 6 ft. 4 in.
- Boom-swing pivot-offset distance
- 3 in.
- Offset distance, left
- 22 in.
- Offset distance, right
- 28 in.
- Bucket digging force
- 4,994 lb.
- Arm digging force
- 3,410 lb.
- Swing speed (spring-applied, hydraulically released, automatic swing brake)
- 9.1 rpm
- Boom swing
- 70 deg. left / 60 deg. right
- Travel speed (low)
- 1.8 mph
- Travel speed (high)
- 2.8 mph
- Ground pressure (canopy) (1.17 m arm, standard counterweight, rubber track)
- 25.0 kPa (3.6 psi)
- Ground pressure (cab)
- 25.9 kPa (3.8 psi)
- Lifting capacity over front, blade down (3.0 m radius) (at ground level, canopy, standard arm, rubber track; cab 1,201 kg; limited by hydraulics)
- 2,573 lb.
- Lifting capacity over side (3.0 m radius) (at ground level, canopy; cab 394 kg)
- 781 lb.
Weight
- Operating weight (canopy, 1.17 m arm, standard counterweight, rubber track, full fuel tank, 79 kg operator)
- 5,780 lb.
- Operating weight (cab) (cab, same configuration)
- 6,110 lb.
- Counterweight (canopy) (standard)
- 531 lb.
- Counterweight (cab) (standard)
- 459 lb.
Engine
- Engine model
- Yanmar 3TNV80F
- Emissions
- EPA Final Tier 4 / EU Stage IV
- Displacement
- 77 cu. in.
- Net power (ISO 9249, at 2,500 rpm)
- 20.0 hp
Hydraulics
- Hydraulic system
- Open center, 2 variable-displacement pumps, 1 fixed-gear pump and 1 pilot pump
- Pump flow (piston, each of 2)
- 7.9 gpm
- Pump flow (gear)
- 4.3 gpm
- Auxiliary flow
- 12.2 gpm
Undercarriage
- Track type
- Rubber, 300 mm wide
- Final drive
- Planetary final drive; 2-speed axial-piston propel motors
Blade
- Blade width
- 4 ft. 11 in.
- Blade height
- 12.6 in.
- HMax blade lift above ground (blade bottom at highest position)
- 13 in.
- IMax blade drop below ground (blade bottom at lowest position)
- 12 in.
Front attachment
- Boom length
- 6 ft. 11 in.
- Arm length
- 3 ft. 10 in.
- Standard bucket width
- 18 in.
Service capacities
- Fuel tank
- 9.0 gal.
- Engine oil, with filter
- 3.9 qt.
- Cooling system
- 3.3 qt.
- Hydraulic tank
- 6.3 gal.