Bobcat E26

Bobcat E26 new-generation 2.6-tonne reduced-tail-swing mini excavator (Yanmar 3TNV76, Stage V, cylinder-inside-boom) as listed by Bobcat Middle East & Africa; figures from the Bobcat E26/E27z/E27 brochure B4501724-EN (09-24), which match the MEA product page; cab, standard dipperstick and 1500 mm blade.

UAEUSAGlobal

digging depth: 8.4 ft
power: 20 hp
Operating weight: 5,750 lb

Side

Front

Overall length: 13.7 ft
Track length: 6.4 ft
Track length on ground: 5.1 ft
Swing centre to blade: 4.8 ft
Swing centre to front (transport): 10.5 ft
Overall height (to top of cab): 8 ft
Height to top of engine cover: 5.1 ft
Ground clearance, counterweight: 1.8 ft
Blade height: 1 ft
Track lug height: 0.1 ft
Blade width: 4.9 ft
Shoe width: 0.8 ft
Tail swing radius: 2.7 ft

Dimensions

Tail swing radius, medium counterweight (P* in the table): 2.8 ft

Performance

BMax digging reach: 14.9 ft
CMax reach at ground level (Working range C): 14.5 ft
KMax digging depth (Working range K): 8.4 ft
JMax vertical wall digging depth (Working range J): 4.8 ft
HMax digging height (Working range H, maximum bucket tooth height): 13.1 ft
IMax dumping height (Working range I): 9.3 ft
GMax height of working equipment, dipperstick retracted (Working range G): 10.2 ft
DMax working equipment radius, boom at max height, dipperstick retracted (Working range D): 6.7 ft
EMax blade height (Working range E, above ground): 1.3 ft
FMax blade depth (Working range F, below ground): 1.4 ft
ABucket rotation (Working range A, bucket pivot angle): 185°
OFront swing radius (minimum) (Plan view O, minimum turning radius): 5.8 ft
MBoom swing offset, left: 1.9 ft
NBoom swing offset, right (Plan view N, right-hand rotation): 2.3 ft
RWorking width at max left-hand rotation (Plan view R): 5.3 ft
QWorking width at max right-hand rotation (Plan view Q): 5.7 ft
Boom swing, left: 60°
Boom swing, right: 60°
Bucket digging force: 5,332 lbf
Arm digging force: 3,527 lbf
Swing speed (Slew rate): 9.3 rpm
Drawbar pull: 6,537 lbf
Travel speed (high): 2.7 mph
Travel speed (low): 1.6 mph

Weight

Operating weight (With cab and bucket, ISO 6016): 5,750 lb
Transport mass (No attachment): 5,461 lb
Weight reduction with canopy: -260 lb
Ground pressure (Rubber tracks): 30.3 kPa

Engine

Engine model: Yanmar 3TNV76-PBC
Emissions: EU Stage V
Cylinders: 3
Displacement: 0.3 US gal
Gross power (Maximum power at 2,400 rpm, ISO 14396): 20 hp
Max torque (At 1,800 rpm, SAE J1995): 49 lbf·ft
Engine oil, with filter: 1 US gal
Cooling system (With heater (3.9 L without)): 1.1 US gal

Hydraulics

Pump flow: 24.9 US gpm
Auxiliary circuit flow (AUX1) (Relief 180 bar): 14.2 US gpm
Auxiliary circuit flow (AUX2) (Relief 179 bar): 5.3 US gpm

Service capacities

Fuel tank: 9.1 US gal
Hydraulic tank (Hydraulic reservoir): 2.7 US gal
Hydraulic system, with tank (System capacity): 6.1 US gal

Service intervals

Engine oil and filter (or 12 months; first change at 50 h): 250 hours
Fuel filters: 250 hours
Hydraulic oil: 500 hours
Hydraulic filter (and case drain filter; first change at 50 h): 500 hours
Final drive oil, first change (then check the level every 250 h): 50 hours
Swing bearing grease (every 10 h when working in water): 50 hours
Pivot points grease: 10 hours
Engine valve clearance (or 12 months): 1,000 hours