Bobcat E26

Bobcat E26 new-generation 2.6-tonne reduced-tail-swing mini excavator (Yanmar 3TNV76, Stage V, cylinder-inside-boom) as listed by Bobcat Middle East & Africa; figures from the Bobcat E26/E27z/E27 brochure B4501724-EN (09-24), which match the MEA product page; cab, standard dipperstick and 1500 mm blade.

UAEUSAGlobal

digging depth: 2.568 m
power: 14.9 kW (20 hp)
Operating weight: 2,608 kg

Side

Front

Overall length: 4.174 m
Track length: 1.965 m
Track length on ground: 1.543 m
Swing centre to blade: 1.462 m
Swing centre to front (transport): 3.192 m
Overall height (to top of cab): 2.438 m
Height to top of engine cover: 1.54 m
Ground clearance, counterweight: 0.539 m
Blade height: 0.319 m
Track lug height: 0.021 m
Blade width: 1.5 m
Shoe width: 0.25 m
Tail swing radius: 0.82 m

Dimensions

Tail swing radius, medium counterweight (P* in the table): 0.84 m

Performance

BMax digging reach: 4.542 m
CMax reach at ground level (Working range C): 4.413 m
KMax digging depth (Working range K): 2.568 m
JMax vertical wall digging depth (Working range J): 1.474 m
HMax digging height (Working range H, maximum bucket tooth height): 4.006 m
IMax dumping height (Working range I): 2.845 m
GMax height of working equipment, dipperstick retracted (Working range G): 3.104 m
DMax working equipment radius, boom at max height, dipperstick retracted (Working range D): 2.052 m
EMax blade height (Working range E, above ground): 0.385 m
FMax blade depth (Working range F, below ground): 0.42 m
ABucket rotation (Working range A, bucket pivot angle): 185°
OFront swing radius (minimum) (Plan view O, minimum turning radius): 1.755 m
MBoom swing offset, left: 0.58 m
NBoom swing offset, right (Plan view N, right-hand rotation): 0.705 m
RWorking width at max left-hand rotation (Plan view R): 1.616 m
QWorking width at max right-hand rotation (Plan view Q): 1.741 m
Boom swing, left: 60°
Boom swing, right: 60°
Bucket digging force: 24 kN
Arm digging force: 16 kN
Swing speed (Slew rate): 9.3 rpm
Drawbar pull: 29 kN
Travel speed (high): 4.3 km/h
Travel speed (low): 2.5 km/h

Weight

Operating weight (With cab and bucket, ISO 6016): 2,608 kg
Transport mass (No attachment): 2,477 kg
Weight reduction with canopy: -118 kg
Ground pressure (Rubber tracks): 30.3 kPa

Engine

Engine model: Yanmar 3TNV76-PBC
Emissions: EU Stage V
Cylinders: 3
Displacement: 1.1 L
Gross power (Maximum power at 2,400 rpm, ISO 14396): 14.9 kW (20 hp)
Max torque (At 1,800 rpm, SAE J1995): 66 Nm
Engine oil, with filter: 3.6 L
Cooling system (With heater (3.9 L without)): 4.3 L

Hydraulics

Pump flow: 94 L/min
Auxiliary circuit flow (AUX1) (Relief 180 bar): 54 L/min
Auxiliary circuit flow (AUX2) (Relief 179 bar): 20 L/min

Service capacities

Fuel tank: 34.4 L
Hydraulic tank (Hydraulic reservoir): 10.2 L
Hydraulic system, with tank (System capacity): 23 L

Service intervals

Engine oil and filter (or 12 months; first change at 50 h): 250 hours
Fuel filters: 250 hours
Hydraulic oil: 500 hours
Hydraulic filter (and case drain filter; first change at 50 h): 500 hours
Final drive oil, first change (then check the level every 250 h): 50 hours
Swing bearing grease (every 10 h when working in water): 50 hours
Pivot points grease: 10 hours
Engine valve clearance (or 12 months): 1,000 hours