Specification sheetIssued 20 November 2026
Case · skid steer loader
Case SV340B
Case SV340B vertical-lift skid steer loader, Tier 4 Final (FPT F5B, 3.4 L, SCR), open cab, 14 x 17.5 tyres, as Case's spec sheet is published by its NZ dealer Mimico (07.25). Dimension letters A-T are the sheet's drawing; bucket lengths and clearance circles use the 72 in (1.83 m) foundry/excavating bucket, weight and capacity tests use a 78 in (1.98 m) bucket.
USAGlobal
- Rated operating capacity
- 1,545 kg
- power
- 63 kW (84 hp)
- Operating weight
- 4,136 kg
3.02 m
1.88 mPerformance
- Rated operating capacity (50% of tipping load; 1,656 kg (3,650 lb) with additional counterweight)
- 1,545 kg
- Tipping load (Measured with 78 in dirt and foundry bucket)
- 3,090 kg
- Breakout force, bucket cylinders (At 217 bar (3,150 psi))
- 42 kN
- Breakout force, lift cylinders (Tip limit, at 217 bar (3,150 psi))
- 30 kN
- Top speed (High range)
- 18.5 km/h
- Travel speed (low range)
- 12.4 km/h
- Lift geometry
- Vertical lift
- Cycle times
- Raise 4.6 s, lower 3.5 s, dump 2.6 s, roll back 2.0 s
- Bucket capacity (78 in dirt and foundry bucket, heaped; 72 in 0.46 m³)
- 0.5 m³
Weight
- Operating weight (Open cab, 165 lb operator, 78 in heavy-duty bucket, full fuel, 14 x 17.5 tyres)
- 4,136 kg
- Shipping weight
- 3,890 kg
- Additional counterweight (Option)
- 136 kg
- Side cab glass (Add-on weight)
- 21 kg
- Glass or polycarbonate cab door (Add-on weight)
- 34 kg
- Suspension seat (Add-on weight)
- 10 kg
Engine
- Engine model
- FPT F5B FL413D*C001, 4-cylinder turbocharged diesel, direct injection, high-pressure common rail
- Emissions
- Tier 4 Final; SCR with DEF, external cooled EGR
- Displacement
- 3.4 L
- Bore
- 99 mm
- Stroke
- 110 mm
- Gross power (SAE J1349 at 2,500 rpm)
- 67 kW (90 hp)
- Net power (SAE J1349 at 2,500 rpm)
- 63 kW (84 hp)
- Max torque (Peak, at 1,400 rpm)
- 383 Nm
- Engine speeds
- Rated 2,500 rpm; high idle 2,500 +/- 25 rpm; low idle 1,150 +/- 25 rpm
- Electrical
- Alternator 160 A; starter 3.2 kW (4.29 hp); 12 V battery, 1,000 cold-cranking A
- Cylinders (Sheet gives the engine as a 4-cylinder FPT F5B; from MIMICO (Case dealer) copy of the Case sheet)
- 4
Hydraulics
- Hydraulic system
- Gear implement pump; 3-spool open-centre series loader valve; servo-assist mechanical drive pump (electro-hydraulic optional)
- Pump flow (Standard auxiliary flow at rated rpm, 100% efficiency)
- 92 L/min
- Pump flow (high flow) (Optional high-flow auxiliary; enhanced high-flow 132.5 L/min (35.0 gal/min))
- 147 L/min
- Max pressure (Loader control valve relief; port reliefs 250 bar raise, 270 bar curl, 250 bar dump)
- 238 bar
- Drive pump flow (Servo-assist mechanical controls, at rated rpm, 97% efficiency; 109 L/min with electro-hydraulic controls)
- 111 L/min
- Drive system relief pressure
- 360 bar
- Drive charge pressure (25 bar with electro-hydraulic controls)
- 25 bar
- Lift cylinders
- Bore 69.85 mm, rod 50.8 mm, stroke 886.5 mm
- Bucket cylinders
- Bore 76.2 mm, rod 38.1 mm, stroke 398 mm
- Final drive
- Single-reduction chain drive, ASA #100 chain (133.4 kN tensile)
Tyres
- Tyres
- 14 x 17.5 (specification tyre)
Service capacities
- Fuel tank
- 96.5 L
- Engine oil, with filter
- 8.5 L
- Hydraulic tank (Reservoir)
- 22.7 L
- Hydraulic system, with tank
- 45.4 L
- Chain tank, each side
- 22.2 L
- Diesel exhaust fluid (DEF)
- 10.7 L